Security

Stoves fireplaces give much of their energy into the room through the hot air and radiation. The cold air passes through the double walls of the furnace hearth, heats up and goes into the room. These devices achieve a particularly high degree of efficiency. Degree of efficiency furnace chimney is determined by its efficiency, and indicates what percentage thermal energy is given to the premises. Degree of efficiency furnace chimney is about 70%, meanwhile, as in fireplaces with open fires majority (70%) of the heat just gets lost. Stoves fireplaces are also equipped with intakes fresh air that allows you to collect the fuel required for combustion air from the basement and other technical facilities. The device of the combustion chamber combustion chamber furnaces, fireplaces “Fireplace” is protected by fireclay plates or sheets of durable vermiculite.

Such protection allows the furnace fireplace made of steel, which makes them lighter than cast iron and brick kilns. Low weight allows the furnace quickly heat and from the first minute to give warmth to the room. In order to stove retains heat as long as possible, its veneer ceramic plates or soapstone. Also developed a system of long-burning, which allows you to slowly burn fuel, and thereby maintain the long process of evolution of heat. Stove, which is equipped with a long burning, at the closed door of the furnace is capable of maintaining high temperature in the furnace up to 10 hours Amenities Furnaces are equipped with metal or glass doors.

If you want to enjoy the live fire fireplace, are the most appropriate model furnaces fireplaces with doors Heat resistant glass. All furnaces firm Fireplace feature roomy ash drawer. Security When you install the furnace-fire should be observed to distances from combustible structures and materials. This distance can vary depending on the furnace model. Before installing the furnace be sure to read the user manual and observe safety requirements. Stoves fireplaces must be installed on the floor of noncombustible materials. Base for the furnace can be completely out of ceramic tile, metal or glass base. Fly zone must be at least 50 cm in front of the stove and at least 20 cm on the sides. Fireplace and chimney must be connected to a chimney only a furnace. Each furnace must have a chimney! Also, Russian construction norms prohibit connecting flue and vents! Installation of the furnace-fire in the finished house fireplace can be installed easily in the final house, which has a chimney. Because of the small weight stove does not require a concrete base and can be installed on wooden floors. In any case, if you want to install stove advise you to consult a specialist.

Garden Site

The appearance of your garden each represents a different way. But all the gardens in common – a place where you can relax from the hustle and bustle, surrounded by wildlife. Every summer resident seeks to acquire a beautiful summer gazebo. As to choose the most appropriate model for such facilities to the site? How to translate ideas into reality? How to make this element of the garden plot is not only functional but also aesthetically appealing? First you need to define the purpose of construction: why put up a conversation in the garden. To become an ideal place to relax, it should be possible to meet the needs of all households. The direct appointment of gazebos in the garden today – expand the functional space holiday home and remove the burden from the veranda, living room or kitchen. Therefore, it is important to provide a device roads and trails that will connect the house, gazebo and, if necessary, household premises. If you plan to install inside the gazebo table and bench, this must be taken into account already in the initial calculation of the size of the structure.

If you plan to place the gazebo next to the barbecue or grill, it is to consider when choosing a site for construction of pavilions to subsequently do not have to trim interfering branches or plants. Garden arbor can serve not only as a place of rest, but at the same time be a bright decorative spot in your garden. To do this you need to consider design design pergola, its location on the site, as well as its functionality. There are many factors that should also be taken into account: the microclimate site mobility of soil, light and shadow angles of incidence from the adjacent buildings, fences and tall trees at different times of day. The most important condition for choosing the site for construction of pavilions – a beautiful view from it.

POWERTEX

Upon completion of all preparatory works (leveling walls, putty, wallpaper pasting, etc.) can begin to paint the walls. Surface quality requirements for color putty walls (without wall for painting) is the same as staining the ceiling (even, smooth, no scratches, surface). It should be remembered that the matte latex paint requires less surface quality than the glossy. When painting walls putty (no wallpaper under painting) should be applied three coats of paint, and the first layer is the ground. As a primer you can use latex paint, which is expected to paint the walls of the main, though most preferably use recommended by the manufacturer of the paint primer. When painting the walls with wallpaper with only two coats of paint (primer is eliminated).

Step 2. Work gloves Gloves. Pour latex paint into a clean bucket (recommended to use a 16-liter plastic buckets firms 'Terraco' with a lid). Adding water, electric mixer with paddle drill "mixer" to bring to the consistency of 'milk'. Attention! If you run a thick paint that dries show more intense staining of bands the joints. White latex paint, for example POWERTEX can be tinted to the desired color using the color scheme, such as Kohler 'Mixol'.

If you are working with Kohler (liquid or powder) should be pre-diluted with water-based paint in a shallow dish, such as a glass ( 100 ml). Gradually add the mixture to the main paint (mixing with a mixer) to achieve the desired intensity. Approximate consumption latex paint for walls (the room with the ceiling area of 16 m ) is equal to 6 or 7 liters. Wait until the foam settles. For painting the walls need to roll with fur fur platen (a roller to coat Nozzle 'PAINTER'S CHOICE' of a light green material for all dull colors. Polypropylene double base resistant to water, solvents and will not crack. For the average surface roughness. Width 22.5 cm, has the effect of 'orange peel', height 16-18 mm nap), brush brush. Soaking water-based paint roller to perform with the bath-bath paint, with paint in a bucket, pour in before the tub, mix with a mixer. Before you start painting the walls should be saturate coat latex paint roller, that is, roll it in a clean, flat surface, such as the back of the unnecessary wallpaper, laid out on the floor (rather 1-1.5 m ). When painting walls putty (no wallpaper under paint) to control the uniformity of staining of the surface (the thickness and texture, blending colors) need more light. In this case, use a cartridge with electric light bulbs with Chuck (Energy-saving lamp of white light at 15 watts, it is recommended to use the shade). Unlike incandescent lamps, more secure and virtually no heat the cartridge. Further highlighting the work surface when painting walls with wallpaper backlight bulbs do not need.

Upland House

In addition, Broken fence triggers off the wind and after its sharp decline. Since the vortices are formed which destroy the soil and greenery. Defining style fencing. Experts advise to choose a fence that will match the style of construction, which actually will ogorazhivat.Esli you are the owner of a small one-story house, then it will be enough wood fence or a fence from the grid. The main purpose of the fence in this case is simply fencing the area from accidental intrusion.

If you are the owner of a large family house, then your options are: a fence of corrugated, welded metal fence, wrought-iron fence. If the house is brick, it is best to fence and was a brick. But at the same time it can be combined, combine elements of different types of fence. For example, if you make the columns of bricks, and the spans of wrought iron gratings or corrugated. Durability.

You must determine how long you expect to use the fence. Keep in mind that no matter how careful you are not treated with a fence made of wood, over time, it still would have to handle or change. Options of other materials are preferred, if you're aiming for longevity of the fence. The height of the fence. If you have decided on the type of fence, you should think about his height. If you have a fence from the grid, you need not do it very high, because it will not be pretty. If you want to use a solid fence to escape the gaze of strangers, it should be the determination of its height and also take into account the position of the plot. If you are on Upland, the angle of the smaller, and can not do a very high fence. If you're in a valley, you will need an increase in height.

Painting

Painting work properly painted walls look is often much better than the laminated walls, to the same apartment where the wallpaper instead of a painted wall looks more modern. For painting of different surfaces used aqueous formulations of paints and synthetic. For the preparation of certain colors and combinations of colors used by selecting Colerne book. When painting walls requires special tools and materials for painting works: brushes, rollers, spatulas. Brush – the main tool of painting works. Rollers are used for painting details. Spatulas used for puttying surfaces.

The technology of painting works before painting the wall surface is cleaned and shpaklyuyut. Fillers, stacked on a metal pan, spatula strokes separate 2-5 mm thick is applied to the surface and well leveled. Putty should only prooliflennye surface. After drying putty sanded coarse-and fine-grained sandpaper. If you are working brushes, brush held perpendicular to the surface. The paint should be applied in one, a shade in the perpendicular direction.

Paint roller surface follows. Roller dipped in a bath of paint and squeeze it on net, set in a bath at a certain angle. Then begin to color, keeping the roller perpendicular to the surface. Each band, applied by roller, should overlap the previous 30-50 mm. On the consumption of paint by pressure on the roller increases. At the junction of different colors and Kolerov to give the walls a finished form, assign panels. To do this, the place of removal of the panels namelennym discourage cable line. To it puts the line of a facet of the painting and fine brush applied to a thin straight line. See also: other – articles and advice

Fiberglass

Rules of operation of plastic windows. To extend the uptime of all the mechanisms of plastic windows Fiberglass manufacturers recommend that the following rules of operation: 1. Twice a year, or, at least annually the service of your plastic windows. It includes: cleaning of parts and mechanisms window fittings of dirt, grease, adjustable locking systems. At least once a year, lubricate the seals is to ensure that they retain their elasticity and provide a good clamping and sealing. Remember that the cost of maintenance on the windows, fittings and seals are much lower than the repair of plastic windows.

2. A simple rule: when you open the window handle must be turned horizontally, Pivoted – strictly vertically. Opening the box with a handle in an intermediate position may cause damage to the locking mechanism control and work on his replacement. 3. Turn the handle is allowed only at closed valve. Trying to turn the force in open state will lead to failure mechanism. 4.

For a sufficiently large width of the leaf (80 inches), it is recommended only opening in the folding position. Remember that the cost of care for windows, adjustment, lubrication parts and mechanisms is much less than the cost of repair or replacement of a hardware box. Repair of plastic windows – this is our specialty and we are ready to offer their expertise and professionalism. 10 reasons to choose us to repair your plastic windows: 1. Of course, our masters behind a solid experience in dealing with windows, since the mid '90s, when the windows with double-glazed were still a novelty for most, they were engaged in assembling, installation, warranty repairs. It allows us to solve almost any problem on the repair of plastic windows with minimal financial cost and as quickly as possible in time. 2. We know and love our work. As you know, if the work is fun – It runs on the 'excellent'. 3. We only work with original, high-quality parts that we order from approved suppliers for years of cooperation. 4. We do not sell boxes. Our specialization – installation and repair plastic windows, and it gives us the ability to qualitatively and lower costs to return your windows original appearance. 5. The task of the activity we see providing maximum comfort and convenience in the home, office, wherever installed plastic windows, using the latest technology and most accurate knowledge about the device physics and windows. 6. Over the years we have accumulated extensive experience in dealing with suppliers and manufacturers of windows, glass and other parts, which allows us to easily and accurately to order any spare parts and make repairs quickly. 7. This also gives us the opportunity to repair any windows, in extreme cases, even using the production facilities window plants. After such a repair you get the window repaired and adjusted to the conditions of production using the latest equipment. 8. We work seven days a week. If you suddenly have difficulty with windows, our expert will try to arrive as quickly as possible and fix the problem on the spot, without any surcharges for urgency. 9. The cost and scope of work are fixed, and they do not change on the ground. 10. Naturally, we give a guarantee all of one year and promptly respond to the challenge.

Investment

How to attract investment into the construction pit on the stage? Where to find investors willing to invest money in it? This question is one of the most important for developers selling apartments in buildings under construction. And the effectiveness of its solution depends on the success of the project, and sometimes the construction itself. Let’s see, what makes a client to invest? He still does not know anything about your company and all that he has a desire invest in real estate. Do you spend time on explaining the merits of a client of the future house, show him graphics, to lay out a card, read out chunks of text advertising in the hope to break the silent indifference, but in response to sound all new questions. It makes no sense to throw his promotional avenues in the hope that he reads and understands all. In the end, having spent 80% of the time you get a promise ring next week. It is difficult to decide on buy a pig in a poke.

The client wants to see a future home and not try to submit it to the words of the sales staff. The right way to successfully demonstrate a nonexistent house to take advantage of it 3D-Modeling modern technology to accurately reproduce on screen the actual object or its prototype in all its completeness. Apartments for sale in standing homes with 3D-technology is still fairly rare. However, judging by the rapid growth in demand for creation of 3D-video movies, in the near future, it offers interesting perspectives. 3D is an animated presentation story about the future of the house, its infrastructure and merits. Viewed 3 5 minute 3D-video, the client quickly perceive and remember the information because it affects him at the same time through a number of visual (text, graphics, video, animation) and sound. Virtual objects have the quality of real materials, surfaces, and precisely convey the shape, color, texture and lighting. Three-dimensional presentation is ready promotional material for the promotion of investment and construction project, through which the company increase sales in the very early development, attract investment, demonstrating a future project in the sales offices and at major events: exhibitions, seminars and conferences.

Enough to run through sites of investment and construction companies to see all the same features of 3D-technology. They provide a “presence effect” and allow the client to see the office, house, cottage from almost any perspective he has chosen, like the floors, the elevator ride, while receiving full information about planning, infrastructure and location of object of interest. Using 3D, you make that clarity, in which the client needs so much. Should I use the power of advertising, attracting a staff of specialists in advertising, public relations and creative ideas in preparation for the construction of a new investment and construction project, if possible to stop the election on modern technologies of 3D-modeling?